• 只能通过司机室内的 S731—7 按钮，方可对旋锁进行手动打开。（集装箱必须处于连接状态）
• 司机室内的信号灯 H762 可指示旋锁是否打开。
在无集装箱状态下
定位销 A 采用机械和电气联锁方式，将旋锁锁定在“打开”位置和“关闭”位置中。
名称 日期 篇 页码
起升与小车运行 03-05-05 EH06-0045 7/45
处于连接状态的集装箱
打开机械式锁定，从而触发感应开关，则旋锁可关闭。
只有机械式锁定锁完全打开后，方可触发该感应开关。如若需要，则应分别对每一个角进行调整。从 S966 开关开始，向上提起定位销 A 。离开这个箱角，使该定位销向上，并可对下一个箱角进行调整。
起升与小车运行
集装箱处于吊起状态
旋锁采用机械方式锁定。此时电气功能无法使用。
当吊起集装箱时，定位销A自由落下，锁住旋锁。感应开关未被触发：转换指令是不可能的。
06.1.3. 吊具T形梁的后端
A 关闭
B 打开
1 S965开关（前端S964开关）
2 旋锁连接杆
3 S966开关（左端S963开关）
4 旋锁转动油缸
5 旋锁关闭位置的S962开关（左端S960开关）
6 旋锁打开位置的S961开关，（左端S959开关）。当两端均处于开的位置时（S61和S59开关被触发），可进行起升。
06.1.4. 微动操作
伸缩式吊具可分别在前端和后端处进行横向微动。通过司机室内（左控制器）的S701－4（后）开关和－6（左）开关以及S701－3开关和－5（右）开关，对Y603（左）阀门和Y604（前）阀门进行控制。
自动回中心功能可以将集装箱移动到中心位置。通过司机室内触摸屏上的按钮，对集装箱进行自动定位。吊具以相应的方向进行移动时，S608开关（左侧前）、S609 开关（左侧后）、S610开关（左侧前）以及S611开关（右侧后）被触发。当对吊具进行定中心后，这些开关均应被归零。
注意! 在操作过程中，如果起升机构或左右倾机构发出任何故障信号（如荷载无法维持在设定的高度），则应立即停止工作，并联系维修人员。
名称 日期 篇 页码
起升与小车运行 03-05-05 EH06-0044 9/45
06.1.5. 润滑点，吊具
S The twist---locks can be opened only manually by means of the button S731--7 in the
cabin. (the container has to be in connection)
S Signal lamp H762 in the cabin indcates opening of the twist---locks.
S963
S964
S965
S966
Without container
The pin A locks the twist--lock B mechanically and electrically both in twist lock open and in
closed position.
Description Date Group Page
Working Devices 03- -05- -05 EH06- -0045 7/45
Container in connection
Mechanical locking is open, the inductive switch is activated. Twist lock can be closed.
The inductive switch must not activate until the mechanical lock is completely open. If neces-
sary, adjust every corner separately. Begin with S966 by lifting the pin A upwards. Leave the
corner so that the pin is up and adjust the next corner.
Page Group Date Description
8/45 EH06- -0045 03- -05- -05 Working Devices
Container hoisted
The twist lock is mechanically locked. Electrical function is impossible.
When a container is hoisted, the pin A is free to drop down and it locks the twist lock
mechanically. The inductive switch is not activated: turn command is not possible.
06.1.3. The rear end of the spreader T- -beam
A Close
B Open
1 S965 (S964 front end)
2 Twist locks connecting rod
3 S966 (S963 Left end)
4 Twist locks turning cylinder
5 S962 Switch of twist locks closed position (S960 Left Side)
6 S961 Switch of twist locks open position (S959 Left Side). When both ends are in
open position (S61 and S59 activated), hoisting is possible.
06.1.4. Side shift operations
The Top--Lift spreader can be shifted transversely at front and rear end separately. Valves
Y603 (Left) and Y604 (front) are controlled by means of switches S701--4 (rear) and --6 (Left)
and S701--3 and --5 (Right) in the cabin (Left Controller).
The automaticcentering can be carried out to move the containerin thecentered position.The
container is automatically centered by means of the push--button in the cabin Touch Display.
Switches S608 (Left side front), S609 (Left side rear) S610 (Right side front) and S611 (Right
side rear) are activated as the Top--Lift spreader is moved in the corresponding direction.
These switches shall be 0--activated as the Top--Lift spreader is centered.
Note! If the lift or trimmechanism shows any signof malfunctionduring
operation - - forexample,theloaddoesnotremainatthesetheight - - stop
working immediately and contact service personnel.
Description Date Group Page
Working Devices 03- -05- -05 EH06- -0044 9/45
06.1.5. Greasing points, Spreader